新聞資訊您當前位置:首頁 > 新聞資訊
給料機控制器的調整方法 |
發布者:admin 點擊:3536 |
1.開啟分析機和風機,及空壓機,脈沖閥10—20分鐘。
2.把控制器上的主機電流調整旋鈕順時針方向調到底。振幅調節旋鈕調到中間位置。
3.啟動主機,把控制器打到自動位置并打開電源開關,緩慢地關閉風機風閥并注意觀察風機電流達到60A時固定,向左或向右旋風機電流調節旋鈕并注意觀察給料機電流表,電流表指針左右擺動即可。
4.全部打開風機風閥,并快速加大給料量《把振幅調節旋鈕順時針方向旋到底即可》同時觀察主機電流,當主機電流達到130A時立即逆時針方向旋動主機電流調節旋鈕,給料機電流表指針左右擺動即可。鎖緊電流調節旋鈕。
5.開機5分鐘左右觀察風機電流是否在60A—65A《順時針方向減小風機電流》微調風機電流調節旋鈕,風機電流穩定在60A—65A觀察5—10分鐘,電流符合要求鎖緊風機電流調節旋鈕。
6.機器運行中如果有輕微落料,微調振幅旋鈕《逆時針方向》。
7.注意:電流調好后一般情況不需要再調節主機和風機電流,控制給料量即可。
中譯英:
1 open analysis machine and the blower, and the air compressor, the pulse valve 10 - 20minutes.
2 controller host current adjusting knob clockwise moved after all. Amplitude adjustment knob to the middle position.
3 boot host, the controller to automatically position and turn on the power switch, slowly closing the fan air valve and observe the fan current reaches 60A fixed, left or right cyclone machine current adjusting knob and observe the feeder current meter, ammeter pointer swing around.
4 all open fan air valve, and the rapid increase of feed quantity" the amplitude adjustment knob clockwise rotation can be observed at the same time the end" current of main host, when the current reaches 130A immediately anti-clockwise rotating hosts a current regulation knob, feeder current meter pointer swing around. Lock current adjusting knob.
5 starting 5 minutes observation fan current is in the 60A - 65A" clockwise to reduce wind mechanical and electrical flow" fine-tuning fan current adjusting knob, fan stable current in60A -65A was observed in 5- 10minutes, current to meet the requirements of locking fan current adjusting knob.
6 the machine is in operation if there is a slight blanking, trimming knob counterclockwise" amplitude".
7 note: current adjusted well in general do not need to adjust host and fan current, control the feeding quantity.
(圖/文w177.cn)
|
上一頁:原煤倉如何更換給料機? 下一頁:刮板輸送機機身注意事項 |