1.由于設備長期運行，故需要經常對提升機的易損件，耗材部件進行檢查、保養、更換等操作。
2.該系統中的主要部件均采用進口件，設計使用壽命均大于5年，或更長。例如：PLC、空氣開關、電機等元器件；但如繼電器器、行程式開關、按扭、選擇開關、等頻繁動作的部件可能出現磨損、打火、燒焦或接觸不良等問題，這些均需要設備維護和使用人員在設備長期工作過程中不斷地保養檢查。
3.如果設備長期沒有使用，在再次使用前一定手動點檢，對可能會造成人身傷害、設備損壞、危險異常情況一定要仔細檢查、定期更換損耗品。
4.請每周對控制柜、遠程分線盒、外露部件(如行程開關、光電開關、接近開關先等)做清潔保養工作，這樣可以防止因?yàn)閴m埃、不潔物對以上元器件造成誤動、假信號、或影響動作精度等危害。
5.每月對控制柜、遠程分線盒內部作定期清潔、視檢等工作，對接線端子、接觸器、繼電器等部件的按線、觸頭進行仔細檢查，以防止有打火、燒焦、粘死、松脫等異常問題。
6.每二個月需對外部電氣部件進行檢查：行程開關有無松動、脫落、壓死、撞損；升降機電機剎車動作是否良好，以防造成馬達煞車抱死，或失靈等故障。
7.每三個月對整個系統設備的所有部件、部品、尤其是外部信號源、執行機構做仔細的點檢、保養、更新；電機是否有噪聲或需添加機油；電機剎車是否需要調節等。
8.每半年需對設備進行停機整修；對主要部件的各種性能、參數，需重新做評估測試；對電氣線路的安全性、可靠性，重新檢查；系統接地、電機絕緣等，做仔細檢查，及易損件的維修更換。
中譯英：
1 because the device runs for a long time, so often need to equipment wearing parts, supplies components are examined, maintenance, replacement and other operations.
2 systems in which the main components are imported parts, the design service life is more than 5 years, or longer. For example: PLC, air switch, motor and other components; but such as relay, switch, button, line program selector switch, and other frequent action parts may wear, ignition, burning or poor contact problems, all these need equipment maintenance and use of personnel in the equipment working process of continuous maintenance check.
3 if the equipment for a long time does not use, before reuse certain manual inspection, likely to cause bodily injury, damage to equipment, dangerous anomalies must be examined carefully, the periodic replacement of the consumer goods.
4 weekly on the control cabinet, remote junction box, the exposed parts ( such as a travel switch, photoelectric switch, close to switch to ) do cleaning and maintenance work, so as to prevent dust, because the unclean on the above components causing malfunction, false signal, or affect the movement accuracy and other hazards.
5 monthly on the control cabinet, remote junction box internal periodic cleaning, inspection work, the terminal, contactor, relay and other parts of the press line, contact check carefully, to prevent ignition, burning, stuck, loose abnormal problem.
6 every two months to be on the external electrical components are examined: the travel switch is loose, falling off, crushed, collision damage; elevator motor brake action is good or not, to avoid causing motor brake lock, or failure fault.
7 every three months for the whole system to all parts of the apparatus, parts, especially the external signal source, implementing agencies do careful inspection, maintenance, update; whether the motor noise or need to add oil; the motor brake need adjustment.
8 per annum for equipment downtime refurbishment; for main components of various properties, parameters, the need to do the evaluation test of electrical circuit; safety, reliability, reexamine; system grounding, electrical insulation, making a careful examination, and wearing parts repair replacement.
(圖/文w177.cn)
|
VR全景
蘇公網安備 32020602000237號